m

LORD Corporation

With more than 3,100 employees in 26 countries, 19 manufacturing facilities and 10 R&D centers worldwide, we're there for our customers.

Our Company

LORD® 201 Acrylic Adhesive Where To Buy


Product Information

LORD® 201 acrylic adhesive when cured with LORD Accelerator 4, 17 or 19 creates an adhesive system that will bond a wide variety of prepared or unprepared metals and plastics. LORD 201 acrylic adhesive in combination with the recommended accelerator replaces welding, brazing, riveting and other mechanical fastening methods.

LORD 201 acrylic adhesive can be cured with either LORD Accelerator 4, LORD Accelerator 17 or LORD Accelerator 19. LORD Accelerator 4 is a no-mix accelerator applied to the substrate before the acrylic adhesive. LORD Accelerators 17 and 19 must be mixed into the acrylic adhesive prior to application. LORD Accelerator 19 is available in off-white or black.

Shelf Life

Shelf life is six months when stored at temperatures under 80°F (27°C) in original, unopened container. Storage temperatures of 40-50°F (4-10°C) are recommended. If stored cold, allow product to return to room temperature before using.

Features and Benefits

Versatile - bonds a wide variety of substrates such as metals, ceramics and plastics; insensitive to minor deviations from correct mix ratio.

Bonds Unprepared Metals - requires little or no substrate preparation.

Self-Leveling - flows into hard-to-reach places and is excellent for bonding irregular shapes.

Environmentally Resistant - resists dilute acids, alkalis, solvents, greases, oils and moisture; provides excellent resistance to indirect UV exposure, salt spray and weathering.

Temperature Resistant - performs at temperatures from -40°F to +300°F (-40°C to +149°C).

UL Rated - when mixed with LORD Accelerator 19, adhesive system is UL 746C certified.

Typical Properties*

Appearance Off-white Liquid
Viscosity, cP @ 77°F (25°C)
Brookfield HAT
Spindle 6, 20 rpm
15,000-55,000
Density, lb/gal (kg/m3) 8.5-8.7 (1019-1042)
Flash Point, °F (°C)
Closed Cup
65 (18)
Work Time, min @ 75°F (24°C) 5-8
Time to Handling Strength, min @ 75°F (24°C) 12-16
Cure Time**, hr 24
Mixed Appearance Color dependent on accelerator used

*Data is typical and not to be used for specification purposes.
**Reaches 90% of ultimate strength after 2 hours.

Guns and Accessories

LORD-Pak™ 50 Replacement 1:1 and 2:1 Plunger
1:1 and 2:1 plunger for use on LORD-Pack 50 manual dispensing gun
LORD-Pak™ 50 Manual Dispensing Gun
handheld, manual dispensing system for small jobs

Features and Benefits

• Approximate linear coverage of mixed adhesive, dispensed as 1/4” bead = 4.5 ft per 50 mL cartridge.

LORD-Pak™ CX Manual Dispensing Gun (Configured for 4:1)
manual dispensing system utilizing a coaxial cartridge containing two adhesive parts

Features and Benefits

• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 38.5 ft per 380 mL cartridge.

LORD-Pak™ CX Pneumatic Dispensing Gun
pneumatic dispensing system utilizing a coaxial cartridge containing two adhesive parts

Features and Benefits

• Approximate linear coverage of mixed adhesive, dispensed as 1/4" bead = 38.5 ft per 380 mL cartridge.
• Maximum dispense pressure = 100 psi.
• Pneumatic air requirements = clean, dry, non-lubricated air or non-flammable gas, 3.2 scfm or less @ 100 psi. Max. air inlet = 1/8" NPT (female). Safety relief valve pop-off = 115 psi.

Mixing Tip 0.25 x 6 x 21 elm. (package of 12)
0.25 x 6 x 21 element, package of 12 - For use with 50 mL
Mixing Tip 0.25 x 6 x 21 elm. (package of 144)
0.25 x 6 x 21 element, package of 144
Mixing Tip 0.375 x 9.5 x 24 elm. (package of 12)
0.375 x 9.5 x 24 element, package of 12
Mixing Tip 0.25 x 7.5 x 24 elm. (package of 12)
0.25 x 7.5 x 24 element, package of 12

Auxiliary Products

LORD<sup>®</sup> 459T Adhesion Enhancer/Surface Modifier

single-component primer in toluene solvent, for direct application; for promoting adhesion of thermoplastic elastomers (TPEs), polyolefins (TPOs) and EPDM

Features and Benefits

Versatile - enhances adhesion to diffi cult-to-bond elastomers, increasing the adhesion of coatings, double-sided tape and adhesives.

Easy to Apply - low viscosity allows for easy application; no mixing required.

Convenient - requires very low dry film weights to enhance adhesion to coatings and double-sided tapes.

LORD<sup>®</sup> 459X Adhesion Enhancer/Surface Modifier

single-component primer in xylene solvent, diluted for direct application; for promoting adhesion of thermoplastic elastomers (TPEs), Polyolefins (TPOs) and EPDM; meets California's VOC requirements

Features and Benefits

Versatile - enhances adhesion to difficult-to-bond elastomers, increasing the adhesion of coatings, double-sided tape and adhesives.

Easy to Apply - low viscosity allows for easy application; no dilution necessary.

Convenient - requires very low dry film weights to enhance adhesion to coatings and double-sided tapes.

LORD<sup>®</sup> 7701 Adhesion Enhancer/Surface Modifier

single-component, solvent-based surface treatment for various vulcanized, thermoplastic polymeric materials

Features and Benefits

Versatile – functions as a cleaner and surface conditioner; treats a wide variety of elastomer functional materials.

Easy to Apply – applies easily by wipe, brush, dip or flood methods.

Convenient – requires no mixing.

Improved Adhesion – improves adhesion to cast urethanes and cured rubber.

Fast Drying – adhesion enhancer/surface modifier flashes off within five minutes or less.

Environmentally Resistant – promotes increased environmental resistance by allowing the treated surface to be more easily wet.

LORD<sup>®</sup> 7713 Adhesion Enhancer/Surface Modifier

single-component, room temperature curing primer; for adhesive bonding of glass reinforced polyester substrates

Features and Benefits

Versatile - enhances adhesion to a variety of substrates when utilized prior to most adhesive applications.

Easy to Apply - low viscosity allows for easy application; no dilution necessary.

LORD<sup>®</sup> Accelerator 4

no-mix accelerator; use with bond thickness of 20 mils or less

Features and Benefits

Convenient – provides room temperature cure with all LORD acrylic adhesives.

Extended Work Time – provides extended assembly time as adhesive does not begin cure until it comes in contact with surface coated with dry accelerator.

Easy to Apply – applies easily by brush, wipe, spray or dip methods onto one or both bonding surfaces.

Fast Cure – dries in approximately one minute to an off-white crystalline film.

Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives.

LORD<sup>®</sup> Accelerator 17

mix-in accelerator; 10:1 mix ratio

Features and Benefits

Convenient - provides room temperature cure with all LORD acrylic adhesives.

Environmentally Friendly - contains no solvent, non-flammable and virtually odorless.

Environmentally Resistant - resists common environmental conditions when used with LORD acrylic adhesives.

LORD<sup>®</sup> Accelerator 19

mix-in accelerator; 2:1 or 4:1 mix ratio

Features and Benefits

Convenient – provides room temperature cure with all LORD acrylic adhesives.

Environmentally Friendly – contains no solvent, non-flammable and virtually odorless.

Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives.

Temperature Resistant – improves high temperature resistance of LORD 200, 400 and 500 series acrylic adhesives.

LORD<sup>®</sup> Accelerator 26

no-mix accelerator; use with bond thicknesses of 20 mils or less; no chlorinated solvents

Features and Benefits

Convenient – provides room temperature cure with all LORD acrylic adhesives.

Extended Work Time – provides extended assembly time as adhesive does not begin cure until it comes in contact with surface coated with dry accelerator.

Easy to Apply – applies easily by brush, wipe, spray or dip methods onto one or both bonding surfaces.

Fast Cure – dries in approximately 15 minutes to an off-white crystalline film.

Environmentally Friendly – does not contain chlorinated solvents.

Environmentally Resistant – resists common environmental conditions when used with LORD acrylic adhesives.

LORD<sup>®</sup> AP-134 Adhesion Enhancer/Surface Modifier

single-component, low viscosity, reactive polymer primer; for glass and ceramics

Features and Benefits

Versatile - provides a wide range of product applications by functioning as a primer to a variety of polar substrates and as an adhesive for reaction injection molding (RIM) of polyurethane to glass.

Easy to Apply - applies easily by spray, dip or polyester felt applicator.

Convenient - requires only a single coat for most applications, reducing labor, solvent usage, inventory and shipping costs.

Literature

Download Type Name
Download Selector Guide LORD Structural Adhesives Selector Guide
Download Technical Data Sheet LORD 201 Acrylic Adhesive
Download Application Guide Structural Adhesive Bonding Application Guide
Download Safety Data Sheet LORD 201

Contact Us