m

LORD Corporation

With more than 3,100 employees in 26 countries, 19 manufacturing facilities and 10 R&D centers worldwide, we're there for our customers.

Our Company

LORD® 306-1/306-2 Epoxy Adhesive Where To Buy


Product Information

LORD® 306 adhesive is a general purpose, high viscosity, two-component epoxy adhesive system used for applications that require gap filling or non-sag characteristics on a vertical surface. This adhesive system conforms to military specification MIL-A-24456 for bonding plastic vibration damping tiles to steel. LORD 306 adhesive can be either room temperature cured or heat cured for faster processing.

Shelf Life

Shelf life is two years from date of manufacture when stored at 60-80°F (16-27°C) in original, unopened container.

LORD 306-1 resin will crystallize if exposed to temperatures below 60°F (16°C), resulting in a lumpy or grainy appearance. If resin exhibits any indication of crystallization, heat material to 80°F (27°C) for 6 hours, mixing occasionally by hand. Be sure to scrape down sides and bottom of container. Continue to heat and mix until material is smooth and homogenous. Allow material to reach room temperature before application.

Features and Benefits

Durable - provides load bearing properties equal to or greater than the materials being bonded.

Environmentally Recommended - contains no solvent, nonflammable and virtually odorless.

Environmentally Resistant - resists moisture, sunlight and weathering.

Temperature Resistant - performs at temperatures from -30°F to +250°F (-34°C to +121°C).

Chemically Resistant - resists dilute acids, alkalis, solvents, greases and oils.

Excellent Engineering Properties - provides low shrinkage, good creep properties and low water absorption.

Non-Sag - remains in position when applied on vertical or overhead surfaces, allowing for greater process flexibility.

Typical Properties*

Work Time, hr @ 75°F (24°C), 54 g mass 1-2
Time to Handling Strength**, hr 8-16
Cure Time**, hr 24-48
Mixed Appearance Grey Paste
Mixed Solids Content by Weight, % 100

*Data is typical and not to be used for specification purposes.
**Temperature dependent. Can be accelerated with heat.

Auxiliary Products

LORD<sup>®</sup> 459T Adhesion Enhancer/Surface Modifier

single-component primer in toluene solvent, for direct application; for promoting adhesion of thermoplastic elastomers (TPEs), polyolefins (TPOs) and EPDM

Features and Benefits

Versatile - enhances adhesion to diffi cult-to-bond elastomers, increasing the adhesion of coatings, double-sided tape and adhesives.

Easy to Apply - low viscosity allows for easy application; no mixing required.

Convenient - requires very low dry film weights to enhance adhesion to coatings and double-sided tapes.

LORD<sup>®</sup> 459X Adhesion Enhancer/Surface Modifier

single-component primer in xylene solvent, diluted for direct application; for promoting adhesion of thermoplastic elastomers (TPEs), Polyolefins (TPOs) and EPDM; meets California's VOC requirements

Features and Benefits

Versatile - enhances adhesion to difficult-to-bond elastomers, increasing the adhesion of coatings, double-sided tape and adhesives.

Easy to Apply - low viscosity allows for easy application; no dilution necessary.

Convenient - requires very low dry film weights to enhance adhesion to coatings and double-sided tapes.

LORD<sup>®</sup> 7701 Adhesion Enhancer/Surface Modifier

single-component, solvent-based surface treatment for various vulcanized, thermoplastic polymeric materials

Features and Benefits

Versatile – functions as a cleaner and surface conditioner; treats a wide variety of elastomer functional materials.

Easy to Apply – applies easily by wipe, brush, dip or flood methods.

Convenient – requires no mixing.

Improved Adhesion – improves adhesion to cast urethanes and cured rubber.

Fast Drying – adhesion enhancer/surface modifier flashes off within five minutes or less.

Environmentally Resistant – promotes increased environmental resistance by allowing the treated surface to be more easily wet.

LORD<sup>®</sup> 7713 Adhesion Enhancer/Surface Modifier

single-component, room temperature curing primer; for adhesive bonding of glass reinforced polyester substrates

Features and Benefits

Versatile - enhances adhesion to a variety of substrates when utilized prior to most adhesive applications.

Easy to Apply - low viscosity allows for easy application; no dilution necessary.

LORD<sup>®</sup> AP-134 Adhesion Enhancer/Surface Modifier

single-component, low viscosity, reactive polymer primer; for glass and ceramics

Features and Benefits

Versatile - provides a wide range of product applications by functioning as a primer to a variety of polar substrates and as an adhesive for reaction injection molding (RIM) of polyurethane to glass.

Easy to Apply - applies easily by spray, dip or polyester felt applicator.

Convenient - requires only a single coat for most applications, reducing labor, solvent usage, inventory and shipping costs.

Literature

Download Type Name
Download MSDS (US) LORD 306-2
Download MSDS (US) LORD 306-1
Download Selector Guide LORD Structural Adhesives Selector Guide
Download Technical Data Sheet LORD 306 Epoxy Adhesive
Download Application Guide Structural Adhesive Bonding Application Guide

Contact Us